Wireless Point to Point Link Kit – Up to 5km

SXT series
SXT is an outdoor wireless router that can be used as a CPE in a PtM setup, or for point to point links. Please
ensure the device is correctly mounted, with the cable pointing straight down.
Assembly and mounting
With the clip pointed forward, slide the mounting bracket into the rail on the bottom of the case, until the clip clicks
into place. The SXT comes bundled with a hose clamp, guide the clamp through the opening in the bracket and
around the pole where it will be mounted. Tighten the hose clamp screw when alignment is complete. Two screw
holes are provided as additional security against accidental bracket movement.
The SXT device has a sliding door, behind which the Ethernet port and the reset jumpers are located. This door can
be also secured shut with a screw in the provided screw hole.
Connecting
• Open the ethernet door to connect an ethernet cable to the ethernet port, connect the other end of the
ethernet cable to the included PoE injector.
• Plug the PoE injector into your network switch or computer.
• Plug the included power supply into the PoE injector to start up the device.
• Set LAN computer IP configuration to automatic (DHCP).
• Default IP address of the unit is 192.168.88.1, open this address in your web browser to start the
configuration. The username is admin and there is no password.
• Please select your country in the screen that loads, to ensure your device meets local regulations. Set a
wireless password, a management password, and upgrade the device to the latest software with the “check
for updates” button.
The device is preconfigured as a wireless client (CPE), and all you need to do is select the AP to connect to and set
a device password. You can do this in the quickSET tab that is loaded by default. In case IP connection is not
available, Winbox can be used to connect to the MAC address of the device.
In case you wish to boot the device from the network, for example, to use MikroTik Netinstall, hold the RESET
button of the device when starting it, until the LED light turns off, then the device will start to look for Netinstall
servers.
We recommend clicking the “Check for updates” button and updating your RouterOS software to the latest version
to ensure the best performance and stability. More information about using RouterOS and connecting to this device
in our documentation: http://mt.lv/help
Powering
The device only accepts 8-32 V power from Passive PoE injectors (one power supply and PoE injector are
included).
Extension Slots and Ports
• One Ethernet (10/100 Mbit or Gigabit, depends on model), supporting automatic cross/straight cable
correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network
devices.
• One Integrated Wireless with built-in directional antenna, max gain 16 dBi.
See mikrotik.com/products for the latest version of this document. Document #49183 Modified on: 03.MAY.2019
Buttons and Jumpers
RouterBOOT reset button has the following functions. Press the button and apply the power, then:
• Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.
• Release the button when the LED turns solid green to clear all configuration and defaults.
• Release the button after LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers
(required for reinstalling RouterOS over the network).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed
before power is applied to the device. Useful for RouterBOOT debugging and recovery.
The device includes a grounding connection behind the ethernet port door (a screw or a metal loop, depending on
model), which you should connect to the grounding installation of the tower or building where the device will be
used. This is to substantially reduce the risk of ESD and lightning damage.
Operating System Support
The device only supports RouterOS software with the version number at or above what is indicated in the
RouterOS menu /system resource.

Specifications

Powering

Wireless

Ethernet

Wireless specifications

Don’t Worry Be Happy

Whether you want an flawless wi-fi network at home or for your business, Maints can set it up for you. No headaches, no fuss, we build a system that fits your needs and install and maintain it for you.  Get in touch with us now for a free quote tailored to your budget and needs.